How to Solve P0719: Turbine Speed Sensor Circuit Intermittent

Car troubles can be frustrating, especially when you encounter an error code like P0719. In this article, we will guide you through the process of solving the P0719 error code related to the turbine speed sensor circuit in your vehicle.

We will cover everything from understanding the error code to diagnosing and fixing the issue step by step. So, let’s dive in and get your car back on the road!

Introduction

The P0719 error code indicates an intermittent issue with the turbine speed sensor circuit in your vehicle’s transmission system. The turbine speed sensor plays a crucial role in monitoring the rotational speed of the input shaft in the transmission.

This information is used by the vehicle’s computer to calculate various factors, such as shift points and torque converter lockup.

car vertical

Understanding the P0719 Error Code

When the vehicle’s computer detects an intermittent fault in the turbine speed sensor circuit, it triggers the P0719 error code. This can occur due to various reasons, including faulty wiring, a malfunctioning sensor, or transmission fluid leaks.

Symptoms of a Faulty Turbine Speed Sensor

Before we proceed with the diagnostic steps, let’s identify some common symptoms that may indicate a faulty turbine speed sensor. Pay attention to the following signs:

  1. Erratic or harsh shifting: You may experience abrupt or delayed shifting between gears, leading to a jerky driving experience.
  2. Slipping transmission: The transmission may slip out of gear or struggle to maintain the correct gear, resulting in a loss of power or acceleration.
  3. Check Engine Light: The illumination of the check engine light on your dashboard is a common indicator of a problem in the vehicle’s system.
  4. Lack of power: Your vehicle may feel sluggish and struggle to accelerate as expected.
  5. Inaccurate speedometer readings: The speedometer may not provide accurate readings or may fluctuate unexpectedly.

If you notice any of these symptoms along with the P0719 error code, it’s crucial to address the issue promptly to avoid further damage to your vehicle’s transmission.

Diagnostic Steps for P0719

To diagnose and resolve the P0719 error code, follow these step-by-step instructions:

Step 1: Check for Transmission Fluid Leaks

Start by inspecting the transmission system for any signs of fluid leaks. Low or contaminated transmission fluid can affect the sensor’s performance and trigger the error code. Ensure that the fluid level is correct and that there are no leaks present. If you notice any leaks, address them accordingly and refill the transmission fluid to the recommended level.

Step 2: Inspect the Turbine Speed Sensor Wiring

Next, examine the wiring harness connected to the turbine speed sensor. Look for any visible damage, loose connections, or corrosion. Faulty wiring can cause intermittent issues and lead to the error code. If you identify any problems with the wiring, repair or replace the damaged sections.

Step 3: Test the Turbine Speed Sensor

To determine if the turbine speed sensor is faulty, you can perform a resistance test using a multimeter. Follow these steps:

  1. Disconnect the electrical connector from the turbine speed sensor.
  2. Set your multimeter to the resistance (ohms) mode.
  3. Connect the multimeter leads to the appropriate pins of the sensor.
  4. Compare the measured resistance with the specifications provided by your vehicle’s manufacturer.
  5. If the resistance reading is significantly different from the expected value, replace the turbine speed sensor.

Replacing the Turbine Speed Sensor

If the diagnostic tests confirm that the turbine speed sensor is faulty, you’ll need to replace it. Here’s a step-by-step guide:

Step 1: Gather the Necessary Tools and Materials

Before you start, gather the required tools and materials. These may include a wrench or socket set, a new turbine speed sensor, and any additional items recommended by your vehicle’s manufacturer.

Step 2: Locate the Turbine Speed Sensor

The turbine speed sensor is typically located on or near the transmission housing. Consult your vehicle’s service manual or online resources specific to your make and model for the exact location.

Step 3: Disconnect the Electrical Connector

Carefully disconnect the electrical connector attached to the turbine speed sensor. Depending on the connector type, you may need to press a release tab or remove a locking mechanism.

Step 4: Remove the Turbine Speed Sensor

Using the appropriate tool, loosen and remove the retaining bolt that secures the sensor in place. Gently pull the sensor straight out of its mounting location.

Step 5: Install the New Turbine Speed Sensor

Take the new turbine speed sensor and align it with the mounting hole. Push it in until it sits snugly. Then, tighten the retaining bolt to secure the sensor in place. Be cautious not to overtighten, as it may damage the sensor or the transmission housing.

Step 6: Reconnect the Electrical Connector

Reconnect the electrical connector to the new turbine speed sensor. Ensure a secure connection is established, and any locking mechanism is engaged.

Clearing the Error Code

After replacing the turbine speed sensor, it’s important to clear the error code from the vehicle’s computer memory. You can do this by using an OBD-II scanner or by disconnecting the vehicle’s battery for a few minutes. However, keep in mind that disconnecting the battery may also reset other settings in your vehicle, such as radio presets or clock settings.

Testing and Verifying the Repair

Once the error code is cleared, take your vehicle for a test drive to ensure the issue has been resolved. Monitor the transmission’s performance and check for any recurrence of the error code or related symptoms. If everything appears normal, congratulations! You’ve successfully solved the P0719 error code.

Tips to Avoid P0719 Error Code

To prevent future occurrences of the P0719 error code, consider the following tips:

  1. Regular maintenance: Follow the recommended maintenance schedule for your vehicle, including transmission fluid checks and replacements.
  2. Address fluid leaks promptly: Any signs of transmission fluid leaks should be addressed promptly to maintain the correct fluid level and prevent sensor issues.
  3. Avoid aggressive driving: Abrupt and harsh shifts can put unnecessary stress on the transmission system. Drive smoothly and avoid sudden acceleration or deceleration whenever possible.

Conclusion

Dealing with the P0719 error code can be overwhelming, but armed with the right knowledge and guidance, you can tackle the issue effectively. In this article, we discussed the causes, symptoms, diagnostic steps, and the process of replacing the turbine speed sensor to solve the P0719 error code. Remember to follow the steps carefully and consult your vehicle’s service manual or seek professional help if needed. By addressing the issue promptly, you can ensure a smooth and trouble-free driving experience.

FAQs (Frequently Asked Questions)

1. Can I continue driving with the P0719 error code?

It’s generally not recommended to drive with the P0719 error code, as it indicates a problem with the turbine speed sensor circuit. Continuing to drive with this issue may lead to further damage to your vehicle’s transmission. It’s best to address the problem as soon as possible.

2. Can I fix the P0719 error code myself, or do I need a professional?

While it’s possible to diagnose and fix the P0719 error code yourself, it requires a good understanding of automotive systems and some mechanical skills. If you’re confident in your abilities, you can follow the steps outlined in this article. However, if you’re unsure or uncomfortable with the process, it’s recommended to seek assistance from a professional mechanic.

3. Are there any other error codes related to the turbine speed sensor?

Yes, there are other error codes that may be associated with the turbine speed sensor, such as P0715 (Turbine Speed Sensor Circuit Malfunction) and P0720 (Output Speed Sensor Circuit Malfunction). These codes indicate different issues with the sensor or its circuit. If you encounter any of these error codes, similar diagnostic steps can be followed to identify and resolve the problem.